Recall ID # 97V131000 - VEHICLE SPEED CONTROL
| Recall Date: |
AUG 19, 1997 |
| Component: |
VEHICLE SPEED CONTROL |
| Model Affected: |
325IS |
| Potential Units Affected: |
410000
Recall Details
|
Recall Date:
AUG 19, 1997
Model Affected:
1995 BMW 325IS
Summary:
THE CRUISE CONTROL AND THROTTLE CABLES ARE ATTACHED TO THE SAME THROTTLE VALVE ACTUATING LEVER AT THE THROTTLE HOUSING. IT IS POSSIBLE THAT THE PLASTIC BUSHING ON EITHER CABLE COULD BREAK DUE TO ENVIRONMENTAL INFLUENCES COUPLED WITH VIBRATION. IF THE BUSHING BREAKS, THE OUTER CABLE HOUSING CAN SEPARATE FROM THE BUSHING. IN THIS CASE, DURING APPLICATION OF THE THROTTLE PEDAL WITHOUT CRUISE CONTROL BEING ENGAGED, THE OUTER TUBE COULD CATCH ON THE EDGE OF THE BROKEN BUSHING.
Consequence:
THIS COULD CAUSE THE THROTTLE VALVE TO REMAIN PARTIALLY OPEN. IT HIS WERE TO OCCUR, THE CAR MIGHT NOT DECELERATE AS EXPECTED INCREASING THE RISK OF A VEHICLE CRASH.
Remedy:
DEALERS WILL INSTALL A SPRING STEEL CLIP ON THE OUTER TUBE OF EACH CABLE IN THE AREA OF THE ADJUSTING SCREW AND PLASTIC BUSHING. THE CLIP IS DESIGNED TO PREVENT THE OUTER TUBE FROM DISLODGING FROM THE BUSHING.
Potential Units Affected:
410000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 97V131000 - VEHICLE SPEED CONTROL
| Recall Date: |
AUG 19, 1997 |
| Component: |
VEHICLE SPEED CONTROL |
| Model Affected: |
325I |
| Potential Units Affected: |
410000
Recall Details
|
Recall Date:
AUG 19, 1997
Model Affected:
1995 BMW 325I
Summary:
THE CRUISE CONTROL AND THROTTLE CABLES ARE ATTACHED TO THE SAME THROTTLE VALVE ACTUATING LEVER AT THE THROTTLE HOUSING. IT IS POSSIBLE THAT THE PLASTIC BUSHING ON EITHER CABLE COULD BREAK DUE TO ENVIRONMENTAL INFLUENCES COUPLED WITH VIBRATION. IF THE BUSHING BREAKS, THE OUTER CABLE HOUSING CAN SEPARATE FROM THE BUSHING. IN THIS CASE, DURING APPLICATION OF THE THROTTLE PEDAL WITHOUT CRUISE CONTROL BEING ENGAGED, THE OUTER TUBE COULD CATCH ON THE EDGE OF THE BROKEN BUSHING.
Consequence:
THIS COULD CAUSE THE THROTTLE VALVE TO REMAIN PARTIALLY OPEN. IT HIS WERE TO OCCUR, THE CAR MIGHT NOT DECELERATE AS EXPECTED INCREASING THE RISK OF A VEHICLE CRASH.
Remedy:
DEALERS WILL INSTALL A SPRING STEEL CLIP ON THE OUTER TUBE OF EACH CABLE IN THE AREA OF THE ADJUSTING SCREW AND PLASTIC BUSHING. THE CLIP IS DESIGNED TO PREVENT THE OUTER TUBE FROM DISLODGING FROM THE BUSHING.
Potential Units Affected:
410000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 97V131000 - VEHICLE SPEED CONTROL
| Recall Date: |
AUG 19, 1997 |
| Component: |
VEHICLE SPEED CONTROL |
| Model Affected: |
325IC |
| Potential Units Affected: |
410000
Recall Details
|
Recall Date:
AUG 19, 1997
Model Affected:
1995 BMW 325IC
Summary:
THE CRUISE CONTROL AND THROTTLE CABLES ARE ATTACHED TO THE SAME THROTTLE VALVE ACTUATING LEVER AT THE THROTTLE HOUSING. IT IS POSSIBLE THAT THE PLASTIC BUSHING ON EITHER CABLE COULD BREAK DUE TO ENVIRONMENTAL INFLUENCES COUPLED WITH VIBRATION. IF THE BUSHING BREAKS, THE OUTER CABLE HOUSING CAN SEPARATE FROM THE BUSHING. IN THIS CASE, DURING APPLICATION OF THE THROTTLE PEDAL WITHOUT CRUISE CONTROL BEING ENGAGED, THE OUTER TUBE COULD CATCH ON THE EDGE OF THE BROKEN BUSHING.
Consequence:
THIS COULD CAUSE THE THROTTLE VALVE TO REMAIN PARTIALLY OPEN. IT HIS WERE TO OCCUR, THE CAR MIGHT NOT DECELERATE AS EXPECTED INCREASING THE RISK OF A VEHICLE CRASH.
Remedy:
DEALERS WILL INSTALL A SPRING STEEL CLIP ON THE OUTER TUBE OF EACH CABLE IN THE AREA OF THE ADJUSTING SCREW AND PLASTIC BUSHING. THE CLIP IS DESIGNED TO PREVENT THE OUTER TUBE FROM DISLODGING FROM THE BUSHING.
Potential Units Affected:
410000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 97V131000 - VEHICLE SPEED CONTROL
| Recall Date: |
AUG 19, 1997 |
| Component: |
VEHICLE SPEED CONTROL |
| Model Affected: |
318IC |
| Potential Units Affected: |
410000
Recall Details
|
Recall Date:
AUG 19, 1997
Model Affected:
1995 BMW 318IC
Summary:
THE CRUISE CONTROL AND THROTTLE CABLES ARE ATTACHED TO THE SAME THROTTLE VALVE ACTUATING LEVER AT THE THROTTLE HOUSING. IT IS POSSIBLE THAT THE PLASTIC BUSHING ON EITHER CABLE COULD BREAK DUE TO ENVIRONMENTAL INFLUENCES COUPLED WITH VIBRATION. IF THE BUSHING BREAKS, THE OUTER CABLE HOUSING CAN SEPARATE FROM THE BUSHING. IN THIS CASE, DURING APPLICATION OF THE THROTTLE PEDAL WITHOUT CRUISE CONTROL BEING ENGAGED, THE OUTER TUBE COULD CATCH ON THE EDGE OF THE BROKEN BUSHING.
Consequence:
THIS COULD CAUSE THE THROTTLE VALVE TO REMAIN PARTIALLY OPEN. IT HIS WERE TO OCCUR, THE CAR MIGHT NOT DECELERATE AS EXPECTED INCREASING THE RISK OF A VEHICLE CRASH.
Remedy:
DEALERS WILL INSTALL A SPRING STEEL CLIP ON THE OUTER TUBE OF EACH CABLE IN THE AREA OF THE ADJUSTING SCREW AND PLASTIC BUSHING. THE CLIP IS DESIGNED TO PREVENT THE OUTER TUBE FROM DISLODGING FROM THE BUSHING.
Potential Units Affected:
410000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 97V131000 - VEHICLE SPEED CONTROL
| Recall Date: |
AUG 19, 1997 |
| Component: |
VEHICLE SPEED CONTROL |
| Model Affected: |
318TI |
| Potential Units Affected: |
410000
Recall Details
|
Recall Date:
AUG 19, 1997
Model Affected:
1995 BMW 318TI
Summary:
THE CRUISE CONTROL AND THROTTLE CABLES ARE ATTACHED TO THE SAME THROTTLE VALVE ACTUATING LEVER AT THE THROTTLE HOUSING. IT IS POSSIBLE THAT THE PLASTIC BUSHING ON EITHER CABLE COULD BREAK DUE TO ENVIRONMENTAL INFLUENCES COUPLED WITH VIBRATION. IF THE BUSHING BREAKS, THE OUTER CABLE HOUSING CAN SEPARATE FROM THE BUSHING. IN THIS CASE, DURING APPLICATION OF THE THROTTLE PEDAL WITHOUT CRUISE CONTROL BEING ENGAGED, THE OUTER TUBE COULD CATCH ON THE EDGE OF THE BROKEN BUSHING.
Consequence:
THIS COULD CAUSE THE THROTTLE VALVE TO REMAIN PARTIALLY OPEN. IT HIS WERE TO OCCUR, THE CAR MIGHT NOT DECELERATE AS EXPECTED INCREASING THE RISK OF A VEHICLE CRASH.
Remedy:
DEALERS WILL INSTALL A SPRING STEEL CLIP ON THE OUTER TUBE OF EACH CABLE IN THE AREA OF THE ADJUSTING SCREW AND PLASTIC BUSHING. THE CLIP IS DESIGNED TO PREVENT THE OUTER TUBE FROM DISLODGING FROM THE BUSHING.
Potential Units Affected:
410000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
325I |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1995 BMW 325I
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
318ISA |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1995 BMW 318ISA
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
318ICA |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1995 BMW 318ICA
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
325IC |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1995 BMW 325IC
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
325ISA |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1995 BMW 325ISA
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
325IA |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1995 BMW 325IA
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
318IC |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1995 BMW 318IC
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
318IA |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1995 BMW 318IA
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
325IS |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1995 BMW 325IS
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
325ICA |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1995 BMW 325ICA
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 95V071000 - EQUIPMENT:OTHER:LABELS
| Recall Date: |
APR 03, 1995 |
| Component: |
EQUIPMENT:OTHER:LABELS |
| Model Affected: |
318ICA |
| Potential Units Affected: |
5200
Recall Details
|
Recall Date:
APR 03, 1995
Model Affected:
1995 BMW 318ICA
Summary:
AN OVERSTATEMENT WAS MADE OF THE VEHICLE LOAD CAPACITY AND DESIGNATED SEATING CAPACITY ON THE TIRE INFORMATION PLACARD. THIS DOES NOT MEET THE REQUIREMENTS OF FMVSS NO. 110, "TIRE SELECTION AND RIMS."
Consequence:
CONSEQUENCE OF NON-COMPLIANCE: LOADING OF THE VEHICLE BEYOND THE CAPACITY WEIGHT CAN CAUSE TIRE AND VEHICLE DAMAGE THAT CAN RESULT IN A VEHICLE CRASH.
Remedy:
OWNERS WILL BE MAILED A REVISED PLACARD CONTAING THE CORRECT VEHICLE AND DESIGNATED SEATING CAPACITIES AND INSTRUCTIONS FOR INSTALLING THE PLACARD ON THEIR VEHICLES. IF OWNERS PREFER, THEIR DEALER CAN INSTALL THE PLACARD FOR THEM.
Potential Units Affected:
5200
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 95V071000 - EQUIPMENT:OTHER:LABELS
| Recall Date: |
APR 03, 1995 |
| Component: |
EQUIPMENT:OTHER:LABELS |
| Model Affected: |
318IC |
| Potential Units Affected: |
5200
Recall Details
|
Recall Date:
APR 03, 1995
Model Affected:
1995 BMW 318IC
Summary:
AN OVERSTATEMENT WAS MADE OF THE VEHICLE LOAD CAPACITY AND DESIGNATED SEATING CAPACITY ON THE TIRE INFORMATION PLACARD. THIS DOES NOT MEET THE REQUIREMENTS OF FMVSS NO. 110, "TIRE SELECTION AND RIMS."
Consequence:
CONSEQUENCE OF NON-COMPLIANCE: LOADING OF THE VEHICLE BEYOND THE CAPACITY WEIGHT CAN CAUSE TIRE AND VEHICLE DAMAGE THAT CAN RESULT IN A VEHICLE CRASH.
Remedy:
OWNERS WILL BE MAILED A REVISED PLACARD CONTAING THE CORRECT VEHICLE AND DESIGNATED SEATING CAPACITIES AND INSTRUCTIONS FOR INSTALLING THE PLACARD ON THEIR VEHICLES. IF OWNERS PREFER, THEIR DEALER CAN INSTALL THE PLACARD FOR THEM.
Potential Units Affected:
5200
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 97V131000 - VEHICLE SPEED CONTROL
| Recall Date: |
AUG 19, 1997 |
| Component: |
VEHICLE SPEED CONTROL |
| Model Affected: |
318I |
| Potential Units Affected: |
410000
Recall Details
|
Recall Date:
AUG 19, 1997
Model Affected:
1995 BMW 318I
Summary:
THE CRUISE CONTROL AND THROTTLE CABLES ARE ATTACHED TO THE SAME THROTTLE VALVE ACTUATING LEVER AT THE THROTTLE HOUSING. IT IS POSSIBLE THAT THE PLASTIC BUSHING ON EITHER CABLE COULD BREAK DUE TO ENVIRONMENTAL INFLUENCES COUPLED WITH VIBRATION. IF THE BUSHING BREAKS, THE OUTER CABLE HOUSING CAN SEPARATE FROM THE BUSHING. IN THIS CASE, DURING APPLICATION OF THE THROTTLE PEDAL WITHOUT CRUISE CONTROL BEING ENGAGED, THE OUTER TUBE COULD CATCH ON THE EDGE OF THE BROKEN BUSHING.
Consequence:
THIS COULD CAUSE THE THROTTLE VALVE TO REMAIN PARTIALLY OPEN. IT HIS WERE TO OCCUR, THE CAR MIGHT NOT DECELERATE AS EXPECTED INCREASING THE RISK OF A VEHICLE CRASH.
Remedy:
DEALERS WILL INSTALL A SPRING STEEL CLIP ON THE OUTER TUBE OF EACH CABLE IN THE AREA OF THE ADJUSTING SCREW AND PLASTIC BUSHING. THE CLIP IS DESIGNED TO PREVENT THE OUTER TUBE FROM DISLODGING FROM THE BUSHING.
Potential Units Affected:
410000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
318I |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1995 BMW 318I
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 97V131000 - VEHICLE SPEED CONTROL
| Recall Date: |
AUG 19, 1997 |
| Component: |
VEHICLE SPEED CONTROL |
| Model Affected: |
318IS |
| Potential Units Affected: |
410000
Recall Details
|
Recall Date:
AUG 19, 1997
Model Affected:
1995 BMW 318IS
Summary:
THE CRUISE CONTROL AND THROTTLE CABLES ARE ATTACHED TO THE SAME THROTTLE VALVE ACTUATING LEVER AT THE THROTTLE HOUSING. IT IS POSSIBLE THAT THE PLASTIC BUSHING ON EITHER CABLE COULD BREAK DUE TO ENVIRONMENTAL INFLUENCES COUPLED WITH VIBRATION. IF THE BUSHING BREAKS, THE OUTER CABLE HOUSING CAN SEPARATE FROM THE BUSHING. IN THIS CASE, DURING APPLICATION OF THE THROTTLE PEDAL WITHOUT CRUISE CONTROL BEING ENGAGED, THE OUTER TUBE COULD CATCH ON THE EDGE OF THE BROKEN BUSHING.
Consequence:
THIS COULD CAUSE THE THROTTLE VALVE TO REMAIN PARTIALLY OPEN. IT HIS WERE TO OCCUR, THE CAR MIGHT NOT DECELERATE AS EXPECTED INCREASING THE RISK OF A VEHICLE CRASH.
Remedy:
DEALERS WILL INSTALL A SPRING STEEL CLIP ON THE OUTER TUBE OF EACH CABLE IN THE AREA OF THE ADJUSTING SCREW AND PLASTIC BUSHING. THE CLIP IS DESIGNED TO PREVENT THE OUTER TUBE FROM DISLODGING FROM THE BUSHING.
Potential Units Affected:
410000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
318IS |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1995 BMW 318IS
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE