Recall ID # 97V131000 - VEHICLE SPEED CONTROL
| Recall Date: |
AUG 19, 1997 |
| Component: |
VEHICLE SPEED CONTROL |
| Model Affected: |
318IC |
| Potential Units Affected: |
410000
Recall Details
|
Recall Date:
AUG 19, 1997
Model Affected:
1994 BMW 318IC
Summary:
THE CRUISE CONTROL AND THROTTLE CABLES ARE ATTACHED TO THE SAME THROTTLE VALVE ACTUATING LEVER AT THE THROTTLE HOUSING. IT IS POSSIBLE THAT THE PLASTIC BUSHING ON EITHER CABLE COULD BREAK DUE TO ENVIRONMENTAL INFLUENCES COUPLED WITH VIBRATION. IF THE BUSHING BREAKS, THE OUTER CABLE HOUSING CAN SEPARATE FROM THE BUSHING. IN THIS CASE, DURING APPLICATION OF THE THROTTLE PEDAL WITHOUT CRUISE CONTROL BEING ENGAGED, THE OUTER TUBE COULD CATCH ON THE EDGE OF THE BROKEN BUSHING.
Consequence:
THIS COULD CAUSE THE THROTTLE VALVE TO REMAIN PARTIALLY OPEN. IT HIS WERE TO OCCUR, THE CAR MIGHT NOT DECELERATE AS EXPECTED INCREASING THE RISK OF A VEHICLE CRASH.
Remedy:
DEALERS WILL INSTALL A SPRING STEEL CLIP ON THE OUTER TUBE OF EACH CABLE IN THE AREA OF THE ADJUSTING SCREW AND PLASTIC BUSHING. THE CLIP IS DESIGNED TO PREVENT THE OUTER TUBE FROM DISLODGING FROM THE BUSHING.
Potential Units Affected:
410000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 97V131000 - VEHICLE SPEED CONTROL
| Recall Date: |
AUG 19, 1997 |
| Component: |
VEHICLE SPEED CONTROL |
| Model Affected: |
325IS |
| Potential Units Affected: |
410000
Recall Details
|
Recall Date:
AUG 19, 1997
Model Affected:
1994 BMW 325IS
Summary:
THE CRUISE CONTROL AND THROTTLE CABLES ARE ATTACHED TO THE SAME THROTTLE VALVE ACTUATING LEVER AT THE THROTTLE HOUSING. IT IS POSSIBLE THAT THE PLASTIC BUSHING ON EITHER CABLE COULD BREAK DUE TO ENVIRONMENTAL INFLUENCES COUPLED WITH VIBRATION. IF THE BUSHING BREAKS, THE OUTER CABLE HOUSING CAN SEPARATE FROM THE BUSHING. IN THIS CASE, DURING APPLICATION OF THE THROTTLE PEDAL WITHOUT CRUISE CONTROL BEING ENGAGED, THE OUTER TUBE COULD CATCH ON THE EDGE OF THE BROKEN BUSHING.
Consequence:
THIS COULD CAUSE THE THROTTLE VALVE TO REMAIN PARTIALLY OPEN. IT HIS WERE TO OCCUR, THE CAR MIGHT NOT DECELERATE AS EXPECTED INCREASING THE RISK OF A VEHICLE CRASH.
Remedy:
DEALERS WILL INSTALL A SPRING STEEL CLIP ON THE OUTER TUBE OF EACH CABLE IN THE AREA OF THE ADJUSTING SCREW AND PLASTIC BUSHING. THE CLIP IS DESIGNED TO PREVENT THE OUTER TUBE FROM DISLODGING FROM THE BUSHING.
Potential Units Affected:
410000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 97V131000 - VEHICLE SPEED CONTROL
| Recall Date: |
AUG 19, 1997 |
| Component: |
VEHICLE SPEED CONTROL |
| Model Affected: |
325I |
| Potential Units Affected: |
410000
Recall Details
|
Recall Date:
AUG 19, 1997
Model Affected:
1994 BMW 325I
Summary:
THE CRUISE CONTROL AND THROTTLE CABLES ARE ATTACHED TO THE SAME THROTTLE VALVE ACTUATING LEVER AT THE THROTTLE HOUSING. IT IS POSSIBLE THAT THE PLASTIC BUSHING ON EITHER CABLE COULD BREAK DUE TO ENVIRONMENTAL INFLUENCES COUPLED WITH VIBRATION. IF THE BUSHING BREAKS, THE OUTER CABLE HOUSING CAN SEPARATE FROM THE BUSHING. IN THIS CASE, DURING APPLICATION OF THE THROTTLE PEDAL WITHOUT CRUISE CONTROL BEING ENGAGED, THE OUTER TUBE COULD CATCH ON THE EDGE OF THE BROKEN BUSHING.
Consequence:
THIS COULD CAUSE THE THROTTLE VALVE TO REMAIN PARTIALLY OPEN. IT HIS WERE TO OCCUR, THE CAR MIGHT NOT DECELERATE AS EXPECTED INCREASING THE RISK OF A VEHICLE CRASH.
Remedy:
DEALERS WILL INSTALL A SPRING STEEL CLIP ON THE OUTER TUBE OF EACH CABLE IN THE AREA OF THE ADJUSTING SCREW AND PLASTIC BUSHING. THE CLIP IS DESIGNED TO PREVENT THE OUTER TUBE FROM DISLODGING FROM THE BUSHING.
Potential Units Affected:
410000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 97V131000 - VEHICLE SPEED CONTROL
| Recall Date: |
AUG 19, 1997 |
| Component: |
VEHICLE SPEED CONTROL |
| Model Affected: |
325IC |
| Potential Units Affected: |
410000
Recall Details
|
Recall Date:
AUG 19, 1997
Model Affected:
1994 BMW 325IC
Summary:
THE CRUISE CONTROL AND THROTTLE CABLES ARE ATTACHED TO THE SAME THROTTLE VALVE ACTUATING LEVER AT THE THROTTLE HOUSING. IT IS POSSIBLE THAT THE PLASTIC BUSHING ON EITHER CABLE COULD BREAK DUE TO ENVIRONMENTAL INFLUENCES COUPLED WITH VIBRATION. IF THE BUSHING BREAKS, THE OUTER CABLE HOUSING CAN SEPARATE FROM THE BUSHING. IN THIS CASE, DURING APPLICATION OF THE THROTTLE PEDAL WITHOUT CRUISE CONTROL BEING ENGAGED, THE OUTER TUBE COULD CATCH ON THE EDGE OF THE BROKEN BUSHING.
Consequence:
THIS COULD CAUSE THE THROTTLE VALVE TO REMAIN PARTIALLY OPEN. IT HIS WERE TO OCCUR, THE CAR MIGHT NOT DECELERATE AS EXPECTED INCREASING THE RISK OF A VEHICLE CRASH.
Remedy:
DEALERS WILL INSTALL A SPRING STEEL CLIP ON THE OUTER TUBE OF EACH CABLE IN THE AREA OF THE ADJUSTING SCREW AND PLASTIC BUSHING. THE CLIP IS DESIGNED TO PREVENT THE OUTER TUBE FROM DISLODGING FROM THE BUSHING.
Potential Units Affected:
410000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
318IC |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1994 BMW 318IC
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
318IA |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1994 BMW 318IA
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
325ICA |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1994 BMW 325ICA
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
325IA |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1994 BMW 325IA
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
318ICA |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1994 BMW 318ICA
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
325ISA |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1994 BMW 325ISA
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
325IS |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1994 BMW 325IS
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
325I |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1994 BMW 325I
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
325IC |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1994 BMW 325IC
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
318ISA |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1994 BMW 318ISA
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 96V111000 - SERVICE BRAKES, HYDRAULIC:SWITCHES:BRAKE LIGHT
| Recall Date: |
JUL 01, 1996 |
| Component: |
SERVICE BRAKES, HYDRAULIC:SWITCHES:BRAKE LIGHT |
| Model Affected: |
325IS |
| Potential Units Affected: |
180000
Recall Details
|
Recall Date:
JUL 01, 1996
Model Affected:
1994 BMW 325IS
Summary:
THE BRAKE LIGHT SWITCH CAN FAIL ALLOWING THE SWITCH TO REMAIN IN THE "BRAKE LIGHTS OFF" POSITION OR IN THE "BRAKE LIGHTS ON" POSITION.
Consequence:
IF THIS HAPPENS, THE BRAKE LIGHTS EITHER WILL NOT OPERATE OR WILL BE CONTINUOUSLY ON, REGARDLESS OF BRAKE PEDAL POSITION. FOLLOWING DRIVERS WOULD NOT BE ABLE TO DETERMINE WHETHER THE VEHICLE IS STOPPING, INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.
Remedy:
DEALERS WILL REPLACE THE EXISTING BRAKE LIGHT SWITCH WITH A NEWLY DESIGNED SWITCH.
Potential Units Affected:
180000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 96V111000 - SERVICE BRAKES, HYDRAULIC:SWITCHES:BRAKE LIGHT
| Recall Date: |
JUL 01, 1996 |
| Component: |
SERVICE BRAKES, HYDRAULIC:SWITCHES:BRAKE LIGHT |
| Model Affected: |
325I |
| Potential Units Affected: |
180000
Recall Details
|
Recall Date:
JUL 01, 1996
Model Affected:
1994 BMW 325I
Summary:
THE BRAKE LIGHT SWITCH CAN FAIL ALLOWING THE SWITCH TO REMAIN IN THE "BRAKE LIGHTS OFF" POSITION OR IN THE "BRAKE LIGHTS ON" POSITION.
Consequence:
IF THIS HAPPENS, THE BRAKE LIGHTS EITHER WILL NOT OPERATE OR WILL BE CONTINUOUSLY ON, REGARDLESS OF BRAKE PEDAL POSITION. FOLLOWING DRIVERS WOULD NOT BE ABLE TO DETERMINE WHETHER THE VEHICLE IS STOPPING, INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.
Remedy:
DEALERS WILL REPLACE THE EXISTING BRAKE LIGHT SWITCH WITH A NEWLY DESIGNED SWITCH.
Potential Units Affected:
180000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 96V111000 - SERVICE BRAKES, HYDRAULIC:SWITCHES:BRAKE LIGHT
| Recall Date: |
JUL 01, 1996 |
| Component: |
SERVICE BRAKES, HYDRAULIC:SWITCHES:BRAKE LIGHT |
| Model Affected: |
325IC |
| Potential Units Affected: |
180000
Recall Details
|
Recall Date:
JUL 01, 1996
Model Affected:
1994 BMW 325IC
Summary:
THE BRAKE LIGHT SWITCH CAN FAIL ALLOWING THE SWITCH TO REMAIN IN THE "BRAKE LIGHTS OFF" POSITION OR IN THE "BRAKE LIGHTS ON" POSITION.
Consequence:
IF THIS HAPPENS, THE BRAKE LIGHTS EITHER WILL NOT OPERATE OR WILL BE CONTINUOUSLY ON, REGARDLESS OF BRAKE PEDAL POSITION. FOLLOWING DRIVERS WOULD NOT BE ABLE TO DETERMINE WHETHER THE VEHICLE IS STOPPING, INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.
Remedy:
DEALERS WILL REPLACE THE EXISTING BRAKE LIGHT SWITCH WITH A NEWLY DESIGNED SWITCH.
Potential Units Affected:
180000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 94V037000 - FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM
| Recall Date: |
FEB 17, 1994 |
| Component: |
FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM |
| Model Affected: |
318 |
| Potential Units Affected: |
23500
Recall Details
|
Recall Date:
FEB 17, 1994
Model Affected:
1994 BMW 318
Summary:
THE ADHESIVE MATERIAL OF THE TWO PIECE THROTTLE BODY HEATER MIGRATES INTO THE CIRCULATION CHAMBER CAUSING BUILD UP OF IMPURITIES AND RESTRICTION OF FLOW WITHIN THE CHAMBER. THIS CONDITION AND WATER VAPORS FROM THE CRANK THAT FREEZES AT LOW AMBIENT AIR TEMPERATURES PREVENTS THE THROTTLE PLATE FROM CLOSING AS THE DRIVER RELEASES THE GAS PEDAL, CAUSING LOSS OF THROTTLE CONTROL.
Consequence:
IF LOSS OF THROTTLE CONTROL FROM THE FROZEN THROTTLE BODY OCCURS WHILE THE VEHICLE IS IN MOTION, A VEHICLE CRASH COULD OCCUR.
Remedy:
BMW DEALERS WILL REPLACE THE THROTTLE BODY HEATER WITH A MODIFIED HEATER.
Potential Units Affected:
23500
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 97V131000 - VEHICLE SPEED CONTROL
| Recall Date: |
AUG 19, 1997 |
| Component: |
VEHICLE SPEED CONTROL |
| Model Affected: |
318I |
| Potential Units Affected: |
410000
Recall Details
|
Recall Date:
AUG 19, 1997
Model Affected:
1994 BMW 318I
Summary:
THE CRUISE CONTROL AND THROTTLE CABLES ARE ATTACHED TO THE SAME THROTTLE VALVE ACTUATING LEVER AT THE THROTTLE HOUSING. IT IS POSSIBLE THAT THE PLASTIC BUSHING ON EITHER CABLE COULD BREAK DUE TO ENVIRONMENTAL INFLUENCES COUPLED WITH VIBRATION. IF THE BUSHING BREAKS, THE OUTER CABLE HOUSING CAN SEPARATE FROM THE BUSHING. IN THIS CASE, DURING APPLICATION OF THE THROTTLE PEDAL WITHOUT CRUISE CONTROL BEING ENGAGED, THE OUTER TUBE COULD CATCH ON THE EDGE OF THE BROKEN BUSHING.
Consequence:
THIS COULD CAUSE THE THROTTLE VALVE TO REMAIN PARTIALLY OPEN. IT HIS WERE TO OCCUR, THE CAR MIGHT NOT DECELERATE AS EXPECTED INCREASING THE RISK OF A VEHICLE CRASH.
Remedy:
DEALERS WILL INSTALL A SPRING STEEL CLIP ON THE OUTER TUBE OF EACH CABLE IN THE AREA OF THE ADJUSTING SCREW AND PLASTIC BUSHING. THE CLIP IS DESIGNED TO PREVENT THE OUTER TUBE FROM DISLODGING FROM THE BUSHING.
Potential Units Affected:
410000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
318I |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1994 BMW 318I
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 97V131000 - VEHICLE SPEED CONTROL
| Recall Date: |
AUG 19, 1997 |
| Component: |
VEHICLE SPEED CONTROL |
| Model Affected: |
318IS |
| Potential Units Affected: |
410000
Recall Details
|
Recall Date:
AUG 19, 1997
Model Affected:
1994 BMW 318IS
Summary:
THE CRUISE CONTROL AND THROTTLE CABLES ARE ATTACHED TO THE SAME THROTTLE VALVE ACTUATING LEVER AT THE THROTTLE HOUSING. IT IS POSSIBLE THAT THE PLASTIC BUSHING ON EITHER CABLE COULD BREAK DUE TO ENVIRONMENTAL INFLUENCES COUPLED WITH VIBRATION. IF THE BUSHING BREAKS, THE OUTER CABLE HOUSING CAN SEPARATE FROM THE BUSHING. IN THIS CASE, DURING APPLICATION OF THE THROTTLE PEDAL WITHOUT CRUISE CONTROL BEING ENGAGED, THE OUTER TUBE COULD CATCH ON THE EDGE OF THE BROKEN BUSHING.
Consequence:
THIS COULD CAUSE THE THROTTLE VALVE TO REMAIN PARTIALLY OPEN. IT HIS WERE TO OCCUR, THE CAR MIGHT NOT DECELERATE AS EXPECTED INCREASING THE RISK OF A VEHICLE CRASH.
Remedy:
DEALERS WILL INSTALL A SPRING STEEL CLIP ON THE OUTER TUBE OF EACH CABLE IN THE AREA OF THE ADJUSTING SCREW AND PLASTIC BUSHING. THE CLIP IS DESIGNED TO PREVENT THE OUTER TUBE FROM DISLODGING FROM THE BUSHING.
Potential Units Affected:
410000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 98V178000 - ENGINE AND ENGINE COOLING:COOLING SYSTEM
| Recall Date: |
AUG 04, 1998 |
| Component: |
ENGINE AND ENGINE COOLING:COOLING SYSTEM |
| Model Affected: |
318IS |
| Potential Units Affected: |
340000
Recall Details
|
Recall Date:
AUG 04, 1998
Model Affected:
1994 BMW 318IS
Summary:
VEHICLE DESCRIPTION: PASSENGER VEHICLES. A MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT, SUCH AS A THERMOSTAT, WATER PUMP, OR FAN BELT, CAN RESULT IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND SYSTEM PRESSURE. IF THE INDICATIONS OF A CRITICAL OVERHEATING CONDITION IS NOT NOTICED BY THE DRIVER, IT IS POSSIBLE THAT DAMAGE TO, OR FAILURE OF, A COOLANT SYSTEM COMPONENT COULD OCCUR.
Consequence:
IF A CRACK WERE TO FORM OR A SEAM WERE TO SEPARATE IN THE HEATER CORE END PIECE, HOT COOLANT COULD SUDDENLY BE EXPELLED, INCREASING THE RISK OF PERSONAL INJURY TO A VEHICLE OCCUPANT.
Remedy:
DEALERS WILL INSTALL A NEW DESIGN RADIATOR CAP TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.
Potential Units Affected:
340000
Notes:
BAYERISCHE MOTOREN WERKE
Recall ID # 94V151000 - SEAT BELTS:FRONT:ANCHORAGE
| Recall Date: |
AUG 10, 1994 |
| Component: |
SEAT BELTS:FRONT:ANCHORAGE |
| Model Affected: |
325 |
| Potential Units Affected: |
57000
Recall Details
|
Recall Date:
AUG 10, 1994
Model Affected:
1994 BMW 325
Summary:
IN A FMVSS NO. 208 30 MILES-PER-HOUR COMPLIANCE TEST, AN UNBELTED TEST DRIVER DUMMY'S CHEST MAXIMUM RESULTANT ACCELERATION WAS 70.8 G'S, WHICH EXCEEDS THE MAXIMUM ALLOWABLE VALUE OF 60 G'S. ALSO, THE UNBELTED PASSENGER DUMMY'S LEFT FEMUR MAXIMUM LOAD WAS 2361 LBS, WHICH EXCEEDS MAXIMUM ALLOWABLE VALUE OF 2250 LBS. THE VEHICLES DO NOT COMPLY WITH FMVSS NO. 208, "OCCUPANT CRASH PROTECTION."
Consequence:
CONSEQUENCE OF NON-COMPLIANCE: IN THE EVENT OF AN ACCIDENT, THE OCCUPANT WILL BE SUBJECTED TO AN INCREASED RISK OF INJURY.
Remedy:
ON AUTOMATIC TRANSMISSION MODELS ONLY, THE DEALER WILL REPLACE THE TRANSMISSION SUPPORT CROSSMEMBER WITH A CROSSMEMBER USED ON THE MANUAL TRANSMISSION MODEL. ALSO, THE TRANSMISSION REAR BUSHING SUPPORTS WILL BE REPLACED WITH BUSHING HAVING DIFFERENT PERFORMANCE CHARACTERISTICS. THE STEERING COLUMN FRONT SUPPORT BEARING AT THE FIREWALL WILL BE REPLACED WITH A MODIFIED PART USING A TEFLON INNER SURFACE AND TEFLON SPRAY WILL BE APPLIED TO THE COLUMN HOUSING IN THE AREA OF THE BEARING. A BRACE WILL BE ADDED BETWEEN THE KNEE BOLSTER SUPPORT AND THE STEERING COLUMN.
Potential Units Affected:
57000
Notes:
BAYERISCHE MOTOREN WERKE